Eagle Eye Power Solutions
1-877-805-3377

Voltage & Ground Fault Monitoring

The VGM-Series is an easy-to-use, inexpensive solution for monitoring battery voltage and ground faults. The GFM-100 works for 24V, 48V, 120V, & 240V applications. It reads battery bus status, detects out-of-limit conditions, and provides alarm indications per-user settings. The ground fault monitor’s status, under-voltage, and over-voltage trip values, ground fault, time delay, and IP address settings are easily accessible on the user-friendly color touchscreen interface. Modbus protocol is available on all units. Installation of the VGM-Series monitor is simple – it can be installed as a wall, panel, or DIN rail unit, and includes a mounting kit for DIN rail or wall mounts. A variety of models are available for the VGM-Series, including voltage and ground fault monitoring, or just voltage or ground fault monitoring independently.

Benefici

  • Color touchscreen simple interface
  • Ethernet connectivity to web interface, (4) Form C Contacts
  • Modbus TCP/IP output for all measured parameters
  • Simple installation with mounting kit for DIN rail or wall mount
  • Monitors 24V, 48V, 120V, & 240V batteries
  • Configurations available for different needs
 

specificazioni

Measurement RangeBattery Voltage: 18-32, 38-60, 90-160, 180-320 VDC
Fault Resistance Limit Set: 1 – 100 kOhm
Fault Resistance Limit Set1 – 100 kOhm
Output Contacts(4) Form C
Contact Rating125 VAC/VDC: 0.5A
30VDC: 2A
Maximum Switching Power60 W
Power RequirementsPowered by connected battery DC voltage
Noise ImmunityIEEE/ANSI Standard C 37.90a-1989 compliance
Time Delay to AlarmAdjustable 1 – 999 seconds
Operating EnvironmentTemp: 0 – 55°C (32 – 131°F), Humidity: 0 – 95% RH
Dimensions / Weight147 x 91 x 45 mm (5.77 x 3.56 x 1.77 in) / 284 g (10 oz)
 

FAQs

How does the VGM detect ground fault conditions?

DC ground fault detection is determined by measurement of the voltage imbalance relative to ground. These measurements are made through very high resistance divider networks. One establishes the ground reference, and the other measures the positive and negative DC voltages. These values are applied to analog-to-digital converters, and the microcontroller firmware compares the sum of these DC values to the ground reference. If the sum is 0, the DC voltage is perfectly balanced relative to ground. If the sum is positive or negative, the DC voltage is unbalanced positive or negative. User settings determine the extent of imbalance that will result in an alarm condition.

Will the VGM detect a ground fault via a leaked battery jar?

The system would detect a ground fault via a leaked battery provided the ground fault resistance setting (a user setting) was set to the proper value. Since a leaking jar would result in a path to ground of some resistance, the VGM would sense the resulting voltage imbalance and would alarm, provided the path to ground created by the leak was of a resistance lower than that setting.

What is the k ohm limit for ground detection?

Up to 300k ohm.

What is are the contact ratings for the Form C contacts?

The relays have a contact rating of 60W, with a maximum voltage rating of 220VDC, and a maximum current rating of 2A. With these ratings, this relay can switch 2A at 30VDC or less, 0.5A at 125VDC, but only 0.009A at 220 VDC. An external relay would be needed if the customer wanted to increase the rating past the limit.

Do the connections between the monitor and the batteries need to be fused?

No, the monitor has a built in fuse to protect the monitor. However, you may want to fuse the connections to protect against the possibility of a short circuit occurring in the wiring to the monitor.

Is the VGM CSA certified?

The VGM-Series is CE certified. For Canadian customers, CSA certification is not required on DC powered units. Please contact Eagle Eye with any questions on certification requirements.

Product Training

If you would like product specific training, please contact Eagle Eye directly. We offer complimentary training over the phone. Quotes can be provided for on site product-training. For more information call 1-877-805-3377 or email us at info@eepowersolutions.com. We provide timely support for all inquiries.

EEU Training Courses

Eagle Eye University (EEU) provides scheduled courses tailored to specific aspects of the critical power industry. All courses are also available at your location. The following courses are applicable to Voltage & Ground Fault Monitoring.

Battery 101
Marzo 2, 2020 - Marzo 3, 2020

A comprehensive overview of battery types and how they are used in Standby Power applications

PRC-005-6 Battery Operation & Maintenance Compliance
Novembre 2, 2020 - Novembre 3, 2020

Ensure that operation and maintenance procedures are in compliance with the battery maintenance requirements of NERC PRC-005-6

Comprehensive Battery Training

One or two day non-commercial courses designed around current battery monitoring methods and techniques

video

    Eagle Eye Power Solutions rispetta la tua privacy. Non vendiamo o vendiamo le tue informazioni personali a nessuno. Mai. Leggi la nostra politica sulla privacy.